BD Diesel Cool Down Timer - for X-Monitors (CES)
Welcome to the nation's diesel performance parts experts where we will settle for nothing less than the best. Buy from OC DIESEL and receive excellent customer service on quality components at the lowest price online. Purchase the BD Diesel Cool Down Timer - for X-Monitors (CES) now at this low price for a limited time only.
BD Diesel Cool Down Timer - for X-Monitors (CES) Features
- Protects your Turbo!
- Inexpensive compared to a Turbo!
- Detailed instructions included
- Programmable to your settings
- Specifically designed to send info to the BD X-Monitor
- OC DIESEL Part Number BD 1081100 (BD Diesel Cool Down Timer - for X-Monitors (CES))
1994-2008 6.0L, 6.4L, 7.3L Ford Powerstroke
2001-2009 6.6L GM Duramax LB7, LLY, LBZ, LMM
OC DIESEL Part Number BD 1081100 (BD Diesel Cool Down Timer - for X-Monitors (CES)) will work for 5.9L and 6.7L Dodge Cummins trucks ranging from vehicle manufactured dates 1994-2008; 6.0L, 6.4L, 7.3L Ford Powerstroke trucks ranging from vehicle manufactured dates 1994-2008; 6.6L GM Duramax LB7, LLY, LBZ and LMM trucks ranging from vehicle manufactured dates 2001-2009. This unit is designed to work with the BD Diesel X-Monitor.
Protect your Turbo with a Cool Down Timer
The CDT2 is designed to keep the engine running when the ignition key is turned off and the exhaust temperature is above a set point (between 250-550°F) to prevent
turbocharger bearing failure that could occur when the engine is shut down too quickly. A typical turbocharger can spin in excess of 100,000rpm under load, which will continue
spinning when the engine is turned off.
The turbocharger is lubricated and cooled by the engine oil, and when the engine is turned off, that oil supply is cut off. If a turbocharger is still spinning at a high RPM when
the oil supply is cut off, the internal bearings will utilize what remaining oil around them then start to heat up - essentially cooking the oil, which causes premature bearing failure.
By allowing the turbocharger to slow down to a safe RPM, this bearing failure can be prevented.
How Does a Engine Cool Down Timer 2 Work?
The CDT2 module utilizes the signal from the thermocouple that is measuring the exhaust gas temperature. The thermocouple may already be connected to a gauge or it can be connected to the CDT2 module on its own. When the key is turned off and the exhaust gas temperature is above the shutdown setting, the CDT2 module will keep power supplied to the ECM/PCM, which in turn will keep the engine running until the temperature falls below the setting. As well a new feature of the CDT2 is to shut the truck down based on an adjustable time. This time is adjustable using the potentiometer (knob) on the side of the control unit.
BD Diesel Cool Down Timer has Unique Safety Features
The CDT2 module has a few safety features built-in that the driver should be aware of. If for some reason the exhaust gas temperature does not fall below the shutdown setting within five (5) minutes from the key being turned off, the CDT2 will automatically shutdown the engine. As well if the engine starts to initiate a REGEN cycle causing the EGT's to rise the CDT2 will shut the truck off. The CDT2 module is also designed to monitor the vehicle's hydraulic brakes when it is
connected to the brake pedal switch via the Brake Pedal terminal on the module. While the CDT2 module is keeping the engine alive (ignition key turned off and exhaust gas temperature above the shutdown setting), if the brake pedal is depressed the CDT2 will shutdown the engine.
This was implemented to protect the vehicle from being stolen when the engine is in cool down mode; eventually the brake pedal would have to be pressed which will shutdown the engine preventing the thief from easily driving away with the vehicle. This is also useful in situations where the engine needs to be shutdown immediately or is desired to be shutdown sooner.
This system will work with any "K-Type" EGT Probe found in most pyrometer gauge kits.
Or use BD Thermocouple Probe Kit designed for this application:
PART: BD1081151NOTE: This unit is designed to work in conjunction with BD's own
X-Monitor digital gauge package, connecting between the control module and display.
Buy the BD Diesel Cool Down Timer - for X-Monitors (CES) from OC DIESEL and Save!
Call today and ask for one of our BD Diesel Cool Down Timer - for X-Monitors (CES) Experts! OC DIESEL settles for nothing less than the best customer service with unbeatable prices on the BD 1081100 (BD Diesel Cool Down Timer - for X-Monitors (CES)). Call (714) 848-2170 now.
